本文二维码信息
二维码（扫一下试试看！）
相转移催化剂对高铁酸钾深度处理制浆中段废水的影响
Study on Advanced Treatment of Mid-stage Pulping Effluent by Potassium Ferrate in the Presence of Phase Transfer Catalyst
收稿日期：  
DOI：10.11980/j.issn.0254-508X.2016.02.007
关键词:  相转移催化剂  高铁酸钾  制浆中段废水  深度处理
Key Words:phase transfer catalyst  potassium ferrate  mid-stage pulping effluent  advanced treatment
基金项目:山东省科技重大专项(新兴产业)（2015ZDXX0403B03）；制浆造纸工程国家重点实验室开放基金(201474)。
作者单位
耿士文1 1.青岛科技大学环境与安全工程学院,山东青岛,266042 
贾亚婷1 1.青岛科技大学环境与安全工程学院,山东青岛,266042 
蓝惠霞1,* 1.青岛科技大学环境与安全工程学院,山东青岛,266042 
王晓红1 1.青岛科技大学环境与安全工程学院,山东青岛,266042 
张　恒2,3 2.华南理工大学制浆造纸工程国家重点实验室,广东广州,510640；3.青岛科技大学化工学院,山东青岛,266042 
李军训4 4.泰安生力源生物工程有限公司,山东泰安,271000 
摘要点击次数: 6601
全文下载次数: 1779
摘要:研究了十六烷基三甲基溴化铵(CTAB)、苄基三甲基氯化铵(TMBAC)、四甲基氯化铵(TMAC)和醋酸锰共4种相转移催化剂对高铁酸钾深度处理制浆中段废水的影响。结果表明，4种催化剂的最适pH值均为4；CTAB对处理效果具有明显的促进作用,CTAB用量为0.2 mg/L,高铁酸钾用量为40 mg/L,反应时间为20 min时,CODCr去除率达60%以上；TMAC用量为0.6 mg/L,高铁酸钾用量为40 mg/L,反应时间为20 min时,CODCr去除率达到最大值,为49.3%；TMBAC用量为0.2 mg/L,高铁酸钾用量为60 mg/L,反应时间为20 min时,CODCr去除率达到最大值,为58.4%；醋酸锰加入量为0.6 mg/L,高铁酸钾用量为60 mg/L,反应时间为30 min时,CODCr去除率达到最大值,为56.4%。
Abstract:Effects of four phase transfer catalysts including cetyltrimethyl ammonium bromide (CTAB), benzyl trimethyl ammonium chloride (TMBAC), tetramethyl ammonium chloride (TMAC) and manganese acetate on advanced treatment of mid-stage pulping effluent by potassium ferrate were studied. The results showed that the optimal pH value for the four phase transfer catalysts was 4. CTAB had obviously promoting role on treatment effect, CODCr removal efficiency achived more than 60% when CTAB and potassium ferrate dosages were 0.2 mg/L and 40 mg/L, respectively, and the reaction time was 20 min. When TMAC and potassium ferrate dosages were 0.6 mg/L and 40 mg/L, respectively and reaction time was 20 min, the higest CODCr removal efficiency of 49.3% was achived. While the higest CODCr removal efficiency of 58.4% was achived when TMBAC and potassium ferrate dosages were 0.2 mg/L and 60 mg/L, respectively , and the reaction time was 20 min. When manganese acetate and potassium ferrate dosages were 0.6 mg/L and 60 mg/L, respectively, the reaction time was 30 min, CODCr removal efficiency achieved the higest value of 56.4%.
查看全文  HTML  查看/发表评论  下载PDF阅读器